APM 2.8 V2.8 ArduPilot UAV Flight Controller wi Ublox Neo-6M GPS z 3DR
If You search then APM 2.8 V2.8 ArduPilot UAV Flight Controller wi Ublox Neo-6M GPS z 3DR is best choice, Buy it now for Price is 258.89
Introduction: This is the new APM 2.6 autopilot module
The sensors are exactly the same as with APM2.5+ however this version does not have an onboard compass which makes this version ideal for use with multicopters and rovers
The APM 2.6 is a complete open source autopilot system and the bestselling technology that won the prestigious 2012 Outback Challenge UAV competition
It allows the user to turn any fixed rotary wing or multirotor vehicle (even cars and boats) into a fully autonomous vehicle
capable of performing programmed GPS missions with waypoints
Available with top or side connectors
This revision of the board has no onboard compass which is designed for vehicles (especially multicopters and rovers) where the compass should be placed as far from power and motor sources as possible to avoid magnetic interference
(On fixed wing aircraft its often easier to mount APM far enough away from the motors and ESCs to avoid magnetic interference so this is not as critical but APM 2.6 gives more flexibility in that positioning and is a good choice for them too)
This is designed to be used with the 3DR uBlox GPS with Compass (see option below) so that the GPS/Compass unit can be mounted further from noise sources than APM itself
Features: - Arduino Compatible! - Can be ordered with top entry pins for attaching connectors vertically or as side entry pins to slide your connectors in to either end horizontally - Includes 3-axis gyro accelerometer and magnetometer along with a high-performance barometer - Onboard 4 MegaByte Dataflash chip for automatic datalogging - Optional off-board GPS uBlox LEA-6M module with Compass
- One of the first open source autopilot systems to use Invensenses 6 DoF Accelerometer/Gyro MPU-6000
- Barometric pressure sensor upgraded to MS5611-01BA03 from Measurement Specialties
- Atmels ATMEGA2560 and ATMEGA32U-2 chips for processing and usb functions respectively
GPS Features: - Built-in compass GPS module - Main chip: Ublox LEA-6H - With fast satellite searching speed and high precision - Compatible with APM serial port and I2C port - Includes round plastic shell and GPS support 3DR Radio Telemetry Kit 433Mhz Descriptions: - The 3DR Radio telemetry system is designed as an open source Xbee replacement radio set offering a lower price longer range and superior performance to Xbee radios
It's availabl in 433Mhz
and in the following configurations: serial board (for the air) and USB (for the ground)
- The radio is a 2-way half-duplex wireless communication system with a standard TTL UART interface based on HopeRFs HM-TRP data link modules and custom firmware that improves upon the modules original features and performance
- The SiK firmware includes a bootloader that permits radio firmware upgrades over the serial interface and radio firmware with configurable parameters
Firmware upgrades and configuration are fully supported in the APM Mission Planner
Configuration is also pos
Related Product APM 2.8 V2.8 ArduPilot UAV Flight Controller wi Ublox Neo-6M GPS z 3DR
sunhans 4W (SMA) WiFi Signal Booster 4000mW 2.4Ghz 36dBm
Operating range : 24002500MHz Channel width: 20Mhzz Supported standards: IEEE 802.11b/g/n Operation mode: Bi-directional half-duplex time division duplex Connector type: To radio SMA female (hole inside)
To antenna RP-SMA male (pin inside) Output power: 4000mW (36dBm) Input power: 0 20dBm Transmit gain: 16 - 19dB Receiver gain: 15dB Noise figure: 3.5dB typical Frequency response: 1dB over operating range Power adapter: 6V/4A DC 100240V Operating temperature: -20C to +70C Operating humidity: Up to 75% relative humidity Material: Cast aluminum LED light: Power status / activity status LED Booster weight: 245g Booster size: 10 x 8.6 x 2.1cm Package weight: 550g Package size: 19.5 x 16.1 x 7cm Package contents: 1 x WiFi Signal Booster 1 x RG316 cable with SMA connectors (20cm) 1 x 6dBi omni antenna 1 x power supply
Price : 203.79
UNO R3 Development Board Microcontroller MEGA328P ATMEGA16U2 Compat for Arduino
Features: Using ATMega 16U2 microcontroller Specification: Micro controller: ATmega328 Operating Voltage: 5V Input Voltage (recommended)
7-12V Input Voltage (limits) : 6-20V Digital I/O Pins:14 (of which 6 provide PWM output) Analog Input Pins: 6 DC Current per I/O Pin: 40 mA DC Current for 3.3V Pin: 50 mA Flash Memory: 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM: 2 KB (ATmega328) EEPROM:1 KB (ATmega328) Clock Speed: 16MHz Application Learning board
development board English Manual/Spec http://arduino.cc/en/Main/Software Other: Stitching changes: beside the AREF sutural are two extra I2C pins (SDA and SCL which are copy of Analog 4 and 5 not additional I2C interface)
Beside the RESET also are two extra pins one is IOREF which supports the extension board stand load voltage
The stitching just shows extension board the current on-board voltage
The other one is backup placeholder pins
The RESET circuit is more stable
RESET button position is changed and moved to near the USB interface of voids which is more convenient
ATmega16U2 replaced 8U2 but it does not mean that the 16k flash of R3 can make your code run faster
This upgrade works to the USB interface chip which enables UNO simulate USB HID in theory such as MIDI/Joystick/Keyboard
Packing List: 1 x Development board 1x USB cable (61cm)
Price : 21.29
Womens Watch with hand rope watch with chain
Womens Watch with hand rope watch with chain
Price : 9.99
1-Mode 1600LM CREE XM-L T6 Diving Waterproof LED Flashlight Torch -Chartreuse
US plug charger Input: AC 100V-240V 50/60Hz Output: DC 4.2V 800MA
Price : 32.39
